TM 11-7025-221-20
FOR STORAGE OR SHIPMENT
Section V. PREPARATION
Para
Page
Subject
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2 5 2 - 5 2
Packaging Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2 6 2 - 5 2
Storage Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2 7 2 - 5 3
2-25. General.
This section contains the special instruction required for preparing the equipment for storage or shipment.
Packaging and packing materials must conform to the requirements in SB 38-100, Preservation, Packaging, pock-
ing and Marking Materials, Supplies, and Equipment Used by the Army.
2-26. Packaging Requirements.
The packaging requirements for a TD-1337(V)/G, power supply PS1, and the other replaceable assemblies
are described below.
a. TD-1337(V)/G. The TD-1337(V)/G case is ruggedized, but it is not waterproof. The TD-1337(V)/G
is transportable, plug-in cards are firmly seated in a shock and vibration-resistant card" file. There are
no cables or separate parts to be packaged with a TD-1337(V)/G. A technical manual shipped with a
TD-1337(V)/G is packaged and shipped as described below.
TD-1337(V)/G weighs approximately 62 pounds. Have another person help
you lift and support it to prevent injury to yourself and others.
(1) A technical manual shipped with a TD-1337(V)/G will be wrapped and sealed in waterproof material.
(2) TD-1337(V)/G will be wrapped and sealed in waterproof barrier material before it is placed in a
container for storage or shipment.
b. Power Supply PS1. Power supply is ruggedized, but it is not waterproof. There are no cables
or separate parts to be packaged with the power supply, It should be wrapped and sealed in waterproof
barrier material before it is placed in a container for shipment or storage.
c.
Plug-in Cards, Display Card, and Red CESE Assembly.
NVM card A9 contains a battery. When placing this card in a static-shielding
bag, ensure printed wiring surfaces or connector pins on card do not make
contact with any conductive surfaces. It is possible that contact with a con-
ductive surface could provide a shorting condition that could discharge the
battery.
Plug-in cards, display card, and red CESE assembly must be placed in static-shielding bags prior
to shipment or storage. Use static-shielding bag from which spare assembly was removed. If bag
is missing or damaged, obtain a new bag. Use a static-shielding bag (such as 3M Type 2100)
which has the following characteristics:
Conductive outer layer (surface resistivity of 104 ohms/sq)
q
12
q Non-conductive inner layer (surface resistivity of 10 ohms/sq)
q High tensile and dielectric strength.
2-52